VLAND LED DRL Head Lamps R+L For IS250 IS350 IS220D IS300 2006-2012 Headlights Assembly,With Sequential Indicator (Clear RHD(Driver is on the right))

Product Information

If you receive damage product, please send us clear pictures/video of the defect, we will help you solve the problem ASAP. Ever since installing these, they've infinitely upgraded the look of my IS250 as well as increased visibility at night (the old headlight lenses were hazy).

Once you’ve pulled the old headlamp assembly away from the vehicle a short distance, it’s time to get a full look at wiring harnesses that are attached. While some vendors cut corners, we use advanced LED chips that produce an impressively bright output while consuming less power.

You have to hack trough epoxy glue that holds the lens and that is material that was designed to be as thought as possible.

To do so, find a white wall and a level surface to park on – you can do this inside or outside, but the ground must be level and the wall flat and vertical.Since I live in Hawaii and don’t really do anything besides city driving, I decided I would go with the Vland headlights which are LED only but they look good and were a little cheaper than outright replacing the old with OEM. Whether you wish to rejuvenate your car with modern lighting, replace headlights that have become tarnished and oxidized over the years, Navan products are highly recommended by car enthusiasts ! They can also be found underneath the vehicle where the bumper cover meets splash shields and near the edge of wheel well openings where wheel well liners meet fenders. Four years later, the concept became reality with an almost unchanged design for the production-ready LC. Whether it be aftermarket or OEM, Navan products are notably DOT / SAE (USA, Asia) certified, and equip many vehicles around the world.

Depending on your year and model car, plus the design of the new custom lights, you may need to transfer some bulbs. To understand how to read the volt meter in simple term: When the needle stays constant on high voltage, the wire that was pinch is a Running/Parking light.

You will need to remove the signal bulb from the old lamp (do NOT disconnect any wires) and install it, in its existing housing, into the new lamp. During the warranty period, Vland will replace or repair, at no charge, a product that is defective in materials or workmanship. In the scope of this article, we’ll review the step-by-step basics of installing complete headlight units designed for your specific vehicle. they are plug n play, the outer two lenses are the low beams and those work just fine but the high beams aren’t really good, the lens is narrow. Condensation does not mean that a headlight assembly is defective, and the presence of fogging or misting due to condensation is not considered a valid reason for warranty replacement of the entire headlamp assembly.

Easily control the halos with one of our easy-to-use controllers , and consider the popular ColorSHIFT®, which gives the user RGB control thanks to the 5050 tri-node LEDs that allows you to select any color imaginable. My only complaint is the high beam but I’ve never really had a reason to need them other than turn them on and wonder how they didn’t immediately notice the high beam sucked. Headlight comes with Projector Headlights which provides the maximum beam output while increasing your visibility. We will make all of the electrical connections first, while we have access to the backs of the assemblies. White LED Strip is Daytime Visible bright, 10W Osram LED chips, Brighter than any on the market with supreme quality of Osram!While most condensation in the headlight lens usually dissipates after approximately 20 minutes of driving with the low beams switched on, some small and insignificant areas of the lens may remain misted for a little longer. In my experience, it’ll be an H1 style HID bulb in the headlight assembly with a wire that goes to the ballast and then comes out of the ballast and connects to your factory harness. Removing and re-installing the front bumper cover is relatively easy because most are designed to unbolt and slide off with basic hand tools. After hot, pressurized air has worked its way out of the headlight through the vents, humidity can get drawn in from the outside.